Pencarian Artikel Jurnal & Majalah

Menampilkan keseluruhan arsip dokumen (Halaman 13 dari 34193, Total: 341930 data)

Analisis Tegangan Roda Gigi Miring pada Transmisi Kendaraan Roda Empat berdasarkan AGMA dan ANSYS

Nama Pengarang : Hadi Sutanto
Nama Majalah/Jurnal : Media Teknika
Volume / Nomor Edisi : 12 (No. 1)
Nomor Halaman : 17-25
Abstraksi Narasi : Two kinds of stresses in the gear teeth are root bending stress and tooth contact stress. These two stresses results in the failure of gear teeth. The root bending stress results in fatigue failure and contact stress results in pitting failure at the contact surface. The stress analysis used to minimize gear failure in the design of helical gear. It is also optimize the design of helical gear on the transmission system of the truck motor vehicle, where the power transmission is required at heavy loads with smoother and noiseless operation. In this paper bending stress and contact stress estimated using analytical method while modeling of gears used the numerical solution. Method of beam strength based on modified Lewis calculation used to predict the bending strength of helical gears. Contact stress was estimated using related method of AGMA contact stress. Stress modeling of helical gears is done by ANSYS 14.5, which is a finite element analysis package. The results are then compared with both AGMA and ANSYS procedures. The values of bending strength and contact stress determined using AGMA method found to be compatible with ANSYS simulation.

Penjadwalan Tenaga Kerja untuk Menentukan Regular Days Off (RDOs) dengan Menggunakan Algoritma Monroe

Nama Pengarang : Khalida Syahputri, Jelly Leviza, T Keizerina Devi
Nama Majalah/Jurnal : Media Teknika
Volume / Nomor Edisi : 12 (No. 1)
Nomor Halaman : 10-15
Abstraksi Narasi : ABC Company is a company producing rubber crumb (crumb rubber) in the form of bales with quality SIR 5, SIR 10, and SIR 20. The processing is done consists of several work stations that are continuous. Scheduling the work force in the company is considered less precise in providing holidays and working time, because hiring labor for 7 business days to achieve the production target and exceed 40 hours worked during the week. This is not in accordance with the Decree of the Minister of Manpower of the Republic of Indonesia No.102/MEN/IV/2004 and Law of the Republic of Indonesia No.13 of 2003 on Manpower. So it is necessary to apply a good scheduling system for labor production process, one of the laborscheduling algorithm is to use Monroe. The manpower requirements for the entire production process is as many as 73 people. With the labor scheduling in PT.ABC still can work to meet production targets without disrupting weekday though individual workers get a day off two consecutive days alternately. Another advantage in labor scheduling algorithm Monroe with the company is able to minimize labor costs Rp.232.200.000/year.

Penyusunan Kebutuhan Perancangan Mesin Hemodialisis Menggunakan Kansei Engineering Serta Aplikasi QFD dan TRIZ

Nama Pengarang : Khawarita Siregar, Rosnani Ginting, Ikhsan Siregar
Nama Majalah/Jurnal : Media Teknika
Volume / Nomor Edisi : 12 (No. 1)
Nomor Halaman : 1-9
Abstraksi Narasi : Means of public health is a component in accelerating the improvement of public health degree. Hospitals as health facilities have a very strategic role in providing quality services in accordance with established standards and can reach the whole community. One installation that needs improvement is the quality of instalasai Hemodialysis. The number of patients is increasing every year must be accompanied by improvement of quality of service installation. Based on observations, there were some complaints of patients on hemodialysis installation services. This study intends to improve the quality of care in hemodialysis installations by crafting needs hemodialysis machine design using Kansei Engineering, as well as the application of Quality Function Deployment (QFD) and TRIZ. Kansei Engineering is used to ensure that a service fulfills the desired emotional response. Subsequently used QFD to improve customer satisfaction by improving the quality of services installation hemodialysis. Results of QFD point to contradictions, namely repair and maintenance service of the machine with the alert medics and repair and maintenance of the machine with the cleanliness and comfort of installation. The results showed that the installation of Hemodialysis Patients in fact want a friendly atmosphere of doctors, nurses, and the reception clerk and the condition of hemodialysis machines and devices work properly.

Analisys Of Tensile Strength, Wear Rate, And Cristallinity Of Biocomposite Nano-HA/Magnesium/Shellac Reinforced Cantula Fiber For Bone Screw Material

Nama Pengarang : Dea Pawestry Utami, Joko Triyono, Wijang Wisnu Raharjo, Rachmad Imbang Tritjahjono
Nama Majalah/Jurnal : Mekanika: Majalah Ilmiah Mekanika
Volume / Nomor Edisi : 23 (No. 1)
Nomor Halaman : 75-81
Abstraksi Narasi : Accidents are a major cause of fractures in Indonesia. One of the treatments for fractures is bone screws with support plates that are placed on broken bone. Currently, many biomaterials for bone screws are being developed which have biodegradable properties so that post-operative bone healing is not required. The purpose of this study was to determine the effect of cantula fiber addition on tensile strength, wear rate, and crystallinity of nano-HA/magnesium/shellac bio-composite for bone screw materials. Nano-HA/magnesium/shellac/cantula fiber materials were mixed using a blender. The material was mixed with a magnesium/hydroxyapatite ratio of 70/30 and cantula fiber was added with variations of 0%, 10%, 20% and 30% of total volume. After that, material mixture was compacted with a pressure of 300 MPa for 10 minutes. Then sintering process was carried out at temperature of 140 °C for two hours. The results showed that the highest tensile strength value was 7.86 MPa at 30% variation. The lowest wear rate was 0.31 x 10-3 mm3/Nm at 30% variation. The highest crystallinity in X-Ray Diffraction observations was obtained at 30% variation, which was 79.65%.

Reducing Cogging Torque in V-Shaped BLDC Motors: A FEA Simulation Study on the Impact of Skew Angle

Nama Pengarang : Dewi Rianti Mandasari, Budi Sudiarto, Lia Amelia, Asep Andi Suryandi
Nama Majalah/Jurnal : Mekanika: Majalah Ilmiah Mekanika
Volume / Nomor Edisi : 23 (No. 1)
Nomor Halaman : 64-74
Abstraksi Narasi : This study thoroughly investigated the impact of stator skew angles on cogging torque in V-shape Brushless Direct Current (BLDC) motors, focusing on electric vehicle applications. Using Finite Element Analysis (FEA) with ANSYS Maxwell, the research assessed how variations in stator core skewness affect torque performance, prioritizing the reduction of cogging torque known for inducing undesirable fluctuations during rotor movement, impacting motor smoothness and noise levels. FEA calculations reveal a significant reduction in cogging torque with the introduction of skew angles to the stator core, enhancing motor efficiency. The study introduces novelty by analyzing the magnetic flux distribution resulting from skew angle variations. Simulation results, particularly on no-load characteristics based on D-axis flux linkage data, offer a comprehensive overview of the motor’s response under no mechanical load. Observations showed that D-axis flux linkage values decreased with increasing stator skew angle, indicating a shift in winding angle. This decline in D-axis flux linkage under no-load conditions demonstrates how variations in stator core skew angles impacted magnetic flux distribution, resulting in different values and promoting a more uniform flux linkage waveform. Increased stator core skew angles correlated with reduced flux linkage values, contributing to decreased cogging torque fluctuations and smoother BLDC motor operation.

Analytical Review of Numerical Analysis in Hydrodynamic Performance of the Ship: Effect to Hull-Form Modifications

Nama Pengarang : Aldias Bahatmaka, Deni Fajar Fitriyana, Samsudin Anis, Achmad Yanuar Maulana, Mamad Tamamadin, Sang Won Lee, Joung Hyoung Cho
Nama Majalah/Jurnal : Mekanika: Majalah Ilmiah Mekanika
Volume / Nomor Edisi : 23 (No. 1)
Nomor Halaman : 54-63
Abstraksi Narasi : This review paper provides an overview of simulation-based hydrodynamic design optimization for ship hull forms. It also includes a numerical analysis aimed at accomplish early-stage simulation-based design in terms of hydrodynamic performance. A hydrodynamic module, a hull surface modeling module, and an optimization module are the primary components of this numerical analysis. The hydrodynamic module includes both simple design approaches and high-fidelity numeric tools; these integrated tools are used to evaluate hydrodynamic performances at different design stages. The hull surface modeling module offers a variety of techniques for ship hull surface representation and modification. It is also used to automatically create hull forms or change existing hull forms based on hydrodynamic performance and design constraints. The optimization module includes several optimization algorithms and surrogate models used to determine optimal designs in terms of hydrodynamic performance. Numerical findings indicate that the current tool is well suited for hull form design optimization at the early design stage because it can produce effective optimal designs within a short time.

Enhancing Lubrication System Efficiency in Marine Diesel Engines with Centrifugal Separators - a Case Study Of LPG/C Arimbi: Technical and Cost-Effective Perspectives

Nama Pengarang : Tuswan Tuswan, Muhammad Fuad Rasyad, Untung Budiarto, Ocid Mursid, Andra Tanzani, Serliana Yulianti, Abdi Ismail, Rizky Chandra Ariesta
Nama Majalah/Jurnal : Mekanika: Majalah Ilmiah Mekanika
Volume / Nomor Edisi : 23 (No. 1)
Nomor Halaman : 41-53
Abstraksi Narasi : The lubrication system in an engine is critical for reducing friction between components, preventing wear, reducing heat, protecting components from deposits, and sealing. Maintaining and extending the life of lubricants is crucial for lowering lubricant usage costs. A centrifugal separator is an auxiliary machine that cleans and separates two insoluble liquids with different densities. This study aims to evaluate the efficiency of lubricant life, lubricant usage cost savings, and return on investment time for a centrifugal separator. The study uses a case study of LPG/C Arimbi, where a centrifugal separator has helped maintain lubricants, prevent wear, and separate fuel and free water from lubricants. The centrifugal separator can also maintain Total Base Number (TBN) and viscosity values by filtering solid particles or wear elements up to a size of 0.5 µm. The study found that the difference in lubricant life was 11,780 hours, and the cost savings obtained were IDR 186,456,666 per year. The return on investment time for purchasing a centrifugal separator is three years and two months, assuming an average working hours of LPG/C Arimbi every year of 3,660 hours. Therefore, using a centrifugal separator can improve the efficiency of lubricant life and reduce lubricant usage costs, providing a positive return on investment in the long run.

Magnesium Addition and Treatment of Reinforcement Particles in Al6061 – Sea Sand Composite on Coefficients Friction and Wear Rate

Nama Pengarang : Hammar Ilham Akbar, Muhammad Ilham Arbi Atmaja, Eko Surojo, Bambang Kusharjananta, Reza Aldiansyah Fanani
Nama Majalah/Jurnal : Mekanika: Majalah Ilmiah Mekanika
Volume / Nomor Edisi : 23 (No. 1)
Nomor Halaman : 33-40
Abstraksi Narasi : Aluminium matrix composite is a composite material that can be used as reinforcement to increase the tribological properties of composite. The process of manufacturing the Al6061-Sea sand composite used the stir casting method with stirring time of 10 minutes and speed of 600 rpm. Stir casting specimens were manufactured with height dimension of 20 mm and diameter of 10 mm. After that, the specimen was friction tested using the pin on disc method. The highest coefficient of friction was the specimen without electroless coating with the addition of 2 wt% Mg of 0.634. The more mass fraction of sea sand, the higher the porosity, and the lower the density. An electroless coating process can be carried out on reinforcing particles. This study aims to determine the effect of addition of Mg and treatment of reinforcing particles on the Al6061-Sea sand composite on the coefficient of friction and wear rate. The coefficient of friction, the specimen density increased, the porosity and the wear rate, decreased. This occurred because the reinforcement particle size of sea sand bonded strongly to aluminium matrix. The highest coefficient of friction was the electroless coating with the addition of 2 wt% Mg of sea sand, which was 0.646.

Effect of Boundary Condition on Numerical Study of UAV Composite Skin Panels Under Dynamic Impact Loading

Nama Pengarang : Ilham Bagus Wiranto, Sherly Octavia Saraswati, Iqbal Reza Alfikri, Chairunnisa Chairunnisa, Fadli Cahya Megawanto, Muhammad Ilham Adhynugraha, Nur Cholis Majid
Nama Majalah/Jurnal : Mekanika: Majalah Ilmiah Mekanika
Volume / Nomor Edisi : 23 (No. 1)
Nomor Halaman : 22-32
Abstraksi Narasi : In this study, a dynamic impact loading using Finite Element Analyses (FEA) was applied to an Unmanned Aerial Vehicle (UAV) composite skin panel. Two types of boundary condition panels were investigated (Fixed and Pinned). The composite UAV skin panel consists of upper panel and stiffener which have a thickness of 3 mm and 2 mm, respectively. The material properties used in this study was referring to Hexcel W3G282-F593 technical data sheet. A hemispherical steel indenter with 70 mm diameter and 120 kg of mass was used to crush the panel with a velocity of 4.43 m/s. The finite element analyses were performed using dynamic explicit solver in ABAQUS 6.23. At the beginning of study, the mesh convergence study was conducted to choose the proper mesh for main analysis. The convergence study was simulated using 20 kg mass to shorten computational time. The mesh size of 10 mm was chosen for the main analysis due to convergent result and short computational time compared to others mesh size. The impact deformation, contact force-displacement plot, and contact force-time plot was used to show the differences of using those boundary condition. The results show that fixed and pinned boundary condition reaches its contact force peak with the value of 29.2 kN and 22.8 kN, respectively.

Comparative Analysis of the Size of Glass Fiber Woven Roving based on a Polyester Matrix on the Impact Strength of Composite Materials

Nama Pengarang : M. Fajar Lazuardy, Muhammad Fakhruddin
Nama Majalah/Jurnal : Mekanika: Majalah Ilmiah Mekanika
Volume / Nomor Edisi : 23 (No. 1)
Nomor Halaman : 12-21
Abstraksi Narasi : Laminated Glass Fiber Reinforced Polymer (GFRP) composites are widely used in various industries, such as boat building, car bodies, water tanks and pipelines, which in their use sometimes have the potential to be exposed to impact loads, especially in transportation equipment. Therefore, it is necessary to perform an impact test to determine the toughness value of a composite material against impact loads. This study aims to investigate the characteristics of fibreglass Woven Roving (WR)/polyester composites produced by the compression moulding process to determine the toughness of the composite material concerning changes in weave size. This research uses variations of glass fibre woven roving in sizes of 200 gsm, 400 gsm, 600 gsm. The impact test was conducted following the American Society for Testing Materials (ASTM) D6110-10. The impact test result showed that the lowest impact strength is found in a composite with a woven size of 200 gsm, which is 0.145 J/mm2, and the highest impact strength is found in composite with a woven size of 600 gsm, which is 0.280 J/mm2. 
← Kembali ke Halaman Utama