| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Jurnal Studi Jepang |
| Volume / Nomor Edisi | : | I-I (No. 0) |
| Nomor Halaman | : | 1-18 |
| Abstraksi Narasi | : | - |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Analisa |
| Volume / Nomor Edisi | : | XIV-1, JANUARI (No. 1) |
| Nomor Halaman | : | 43-52 |
| Abstraksi Narasi | : | - |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Analisa |
| Volume / Nomor Edisi | : | XIV-1, JANUARI (No. 1) |
| Nomor Halaman | : | 25-42 |
| Abstraksi Narasi | : | - |
| Nama Pengarang | : | J. Panglaykim. |
| Nama Majalah/Jurnal | : | Analisa |
| Volume / Nomor Edisi | : | XIV-1, JANUARI (No. 1) |
| Nomor Halaman | : | 5-24 |
| Abstraksi Narasi | : | - |
| Nama Pengarang | : | Kamal, Samsul,Tira, Hendry S |
| Nama Majalah/Jurnal | : | Jurnal Teknik |
| Volume / Nomor Edisi | : | 1-1, DESEMBER (No. 1) |
| Nomor Halaman | : | 70-81 |
| Abstraksi Narasi | : | This research was aimed to investigate the change of heat transfer in an interupted fin which is flowed by a main air and disturbing air. The disturbance air is secondary air which flow perpendicular to the main flow. The tlow of such secondary flow is exactly on the each gap between the fin. The change was referred to the term of Nusselt number, pressure reduction and friction factor. Three different interupted fins made of aluminium were employed in this work. Multi purpose air duct was used for providing blowing air. This duct was slightly modified in such away that the disturbating air could flow and touched the fin from two side. The velocity of the inlet air was varied eight times by regulating yhe valve from 5% to 40% with the increase of 5%. Heater was used for heating and 9 thermocouples were used for measuring the temperature. A thermostat was used to regulate the temperature of fin surface. It was found that the highest rate of heat transfer was occurred at the staggered fin with angle of deflection.This fin also had the largest pressure reduction. The lowest of pressure reduction was belonged to in line fin. Friction factor reduced as the velocity of fluid flow is increased. In this experiment, the largest friction factor was ovmed by at the staggered fin with angle of deflection, while the lowest is found at in line fin. Empirical correlation of the thennal perfonnance and friction factor of each fin configuration is defined as: for fin A: for fin B: for fin C: Nu = 0 487 Re05% f = 0,096 Re-{ '·242 Nu = 0,621 Re0533 f = 0 045 Re--0 · 2 15 , Nu = 0 373 Re0582 f = 0 035 Re-0 · 205 |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Jurnal Teknik |
| Volume / Nomor Edisi | : | 1-1, DESEMBER (No. 1) |
| Nomor Halaman | : | 62-69 |
| Abstraksi Narasi | : | Run-in is the initial process to make Spiral Steel Pipe at Spiral Pipe Machine (SPM). The efficient o.f'Spiral Steel Pipe Production depends on Run In process. So far, Spiral Steel Pipe manufacturer used patron to help run-in process. The patron is a function of diameter and thickness of pipe, so this system is not efficient. The aim of this paper is to make the system more efficient by replacing the patron with new design equipment. |
| Nama Pengarang | : | Sutyasadi, Petrus |
| Nama Majalah/Jurnal | : | Jurnal Teknik |
| Volume / Nomor Edisi | : | 1-1, DESEMBER (No. 1) |
| Nomor Halaman | : | 53-61 |
| Abstraksi Narasi | : | Controlling a DC motor usually has several problems. In a second after the DC motor is switched on, the .?ystem will demand a great number of power that usually is called overshoot or power consumption overshoot. How long the system will get their stable position always becomes a serious problem in many cases of control system too. In this case, stable means the motor gets its constant rotation or steady state. Hence. the problems are how to keep the overshoot as low as possible, and as quick as possible for the motor to reach its steady state. This paper shows that with the Optimal Control 711eory, the optimal combination of the outputs can be achieved. |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Jurnal Teknik |
| Volume / Nomor Edisi | : | 1-1, DESEMBER (No. 1) |
| Nomor Halaman | : | 42-52 |
| Abstraksi Narasi | : | Basically, transmission line is resistive, inductive, and capacitive. That will determine the quality of transmission in current or data passing. The quality of the dimension value above can be counted by differential equation, Laplace transform, and hyperbolic us trigonometric identity. This shows the transmission line as an electric circuit. |
| Nama Pengarang | : | Harini, Bernadetta Wuri |
| Nama Majalah/Jurnal | : | Jurnal Teknik |
| Volume / Nomor Edisi | : | 1-1, DESEMBER (No. 1) |
| Nomor Halaman | : | 33-41 |
| Abstraksi Narasi | : | Stepper motor is a dielectric motor that can be controlled with discrete input. it has a good accuracy and precision. lherefvre, stepper motor is widely used in some equipments, such as disk drive in our computer, plotter, robotics, and other control projects. J'he controlling <?/'stepper motor is implemented in Visual Basic 6 language. f'his paper discusses how to use Visual Basic to control two stepper motors that are connected to parallel port, and uses some optical sensors to measure the actual output of those stepper motors, including direction, degree and the amount of motion. |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Jurnal Teknik |
| Volume / Nomor Edisi | : | 1-1, DESEMBER (No. 1) |
| Nomor Halaman | : | 28-32 |
| Abstraksi Narasi | : | Each material always has residual stress which is resulted from some factors, for example temperature changed, forming and stre11gthe11i11g. Pipe forming through rolling causes pull stress and temperature change. This will produce residual stress after pipe.forming finishes. Maximum residual stress resulted from bending momem in pipe is different depending 011 the pipe thickness. Thick pipe has maximum residual stress greater than thin pipe. |