| Nama Pengarang | : | Saleh, Azmi |
| Nama Majalah/Jurnal | : | Jurnal Teknologi Industri |
| Volume / Nomor Edisi | : | 7 (No. 1) |
| Nomor Halaman | : | 19-30 |
| Abstraksi Narasi | : | A distance relay for the transmission lines protection is usually designed on fixed setting range. If the impedance of the transmission lines to he protected is not on the impedance setting range of the distance relay, the relay could not be used. It is purposed the use of backpropagation neural network as a pattern recognizer for distance relay in fault detection by recognizing pattern of voltage an current wave forms. The principle of backpropagation neural network in distance relay is mapping to recognize volhage and current wave forms. Backpropagation neural network is trained supervisely by implementing Generalized Delta Rule algorithm (GDR) to recognize the pattern of voltage and current wave forms of the transmission line in a faulted condition by applying phase voltage and current as the inputs. The output of backpropagation neural network in this opplication is tripino trip decision. If the mapping result in values between 0.5-1.0. the distance relay should send a trip signal to the CB. The distance relay should not send a trip signal result in values between 0.0-0.49. |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Jurnal Teknologi Industri |
| Volume / Nomor Edisi | : | 7 (No. 1) |
| Nomor Halaman | : | 11-18 |
| Abstraksi Narasi | : | This paper will discuss about on academic information system at Informatics Engineering-University of Atma Jaya Yogyakarta (TF UAJY) The system use WAP (Wireless Application Protocol) technology, which means that the technology can he accessed through the mobile phone. System can show the wiversity level instructor schedule and the laboratory schedule. And too improve the system performance. u provide polling facility. With this facility, user can give input to the system, and the user also can get the output from the system, so the system can be a smart information system. In addition, the system offers a lot of functions such as it enable to edit, add. and delete arv lab data with an admin mens. To enter the menu admin must input togin name and password. The system supported by Wireless Morkup Language (WML) on the server side. Hypernest Preprocessor (PHP) on the chent side and MySQL as the database. The system is tested using Nokia 6210 emulator |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Jurnal Teknologi Industri |
| Volume / Nomor Edisi | : | 7 (No. 1) |
| Nomor Halaman | : | 1-10 |
| Abstraksi Narasi | : | In this paper we describe an application of design and implementation of Geographical Information System. This system use thematic maps analysis with overlay method, that applying computer technology to present earth sight information. The input thematic maps are degree of slope, sensibility of soil erosion and daily rates rainfall intensity, that contains geogropical data as spatial data. This data presented in grids as pixel that form the map image at the matrix area. This system able to handle database and appear its in a grapluc, so that can present worth information from programmed analysis result. This system had been tested used thematic maps data of Kabupaten Kulonprogo Bagian horn, D.J Yogyakarta The result are three aren general example of land function that is: area A with arve width 56.250.000 square metres, area B with area width 112.640.625 square metres, and area C with aren width 27.562.500 square metres The system implemented by Microsoft Visual Basic 6.0 and Microsoft Access 2000 |
| Nama Pengarang | : | Julianto, Eddy |
| Nama Majalah/Jurnal | : | Jurnal Teknologi Industri |
| Volume / Nomor Edisi | : | XI (No. 4) |
| Nomor Halaman | : | 359-368 |
| Abstraksi Narasi | : | Remote controlling or monitoring is an alternative for people requiring flexibility for controlling or monitoring devices from arbitrary locations. An example for this application is remote controlling via telephone. Another example is using Web and Internet media to control remote devices. This research aims to develop a web application using Java programming language to monitor devices remotely. In this case, the parameters to be monitored include states of target lamps, temperature and light intensity of target rooms. The steps to be carried out in this research are literature reviews, designing, developing. testing and calibration the electronic system, writing codes for the microcontroller. Other activities included serial communication testing using hyperterminal and Serial Demo from Java and writing and testing the application programs including a web-based client application. |
| Nama Pengarang | : | Wigati, Slamet Setio,Ag. Gatot Bintoro |
| Nama Majalah/Jurnal | : | Jurnal Teknologi Industri |
| Volume / Nomor Edisi | : | XI (No. 4) |
| Nomor Halaman | : | 347-358 |
| Abstraksi Narasi | : | This research studies optimization of replacement based on opportunity for short life cycle system with two-dimensional warranty. System failure during warranty is modeled using the one-dimensional point process formulation where the usage is modeled as a function of time. The opportunity comes randomly and it is modeled as a homogeneous Poisson process with as a parameter. System failure during warranty and after warranty is restored by minimal repair. During the time between the occurrence of opportunity and the time instant of replacement, the user may incur penalty cost due to the delay of replacement. Decision variable for this research is S. which describes an optimum operating time. Optimum value of S (S) is attained by minimizing expected cost per replacement period. Finally some numerical results are also presented to illustrating optimal condition and to analyze influence of warranty period, minimal repair cost. replacement cost and penalty cost to S |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Jurnal Teknologi Industri |
| Volume / Nomor Edisi | : | XI (No. 4) |
| Nomor Halaman | : | 337-346 |
| Abstraksi Narasi | : | The focus of this paper is developing the control strategy on aldehyde distillation column The objective are maintain the consistency of product's composition, energy saving and cost effective. The method is replacing control structure from inferential control to cascade control with LV structure, without replacing and addition instrumentation hardware. Analizer replace by soft sensor to improve performance, reduce cost and increase reliability. The disturbance given by change mole flow rate of feed. Cascade control with LV structure purposed to minimize Internal Absolute Error (IAE) and increase energy efficiency. The result of this research shown that cacscade control with LV structure has lower Integral Absolute Error (IAE) compare to inferential control structure, improved product composition consistency, increase energy efficiency. |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Jurnal Teknologi Industri |
| Volume / Nomor Edisi | : | XI (No. 4) |
| Nomor Halaman | : | 323-336 |
| Abstraksi Narasi | : | Clamp-on ammeters operate based on magnetic field induction, not connected electrically to the measured circuits. This instrument can measure and be removed without disconnecting the circuits. Thus, the reading on their measurements is affected by some factors outside themselves. This research investigated some external factors those may affect the reading of clamp-on ammeter. The external factors were conductor cross-section, insulating size and material, type of load, metal cubicles and other circuit existences for various current magnitudes. The differences of reading were obtained by comparing the clamp-on ammeter measurement results to those the conventional ammeter. From external factors, the largest influence was existence of other circuit line that pass by the clamp. The difference of reading had variation, depend on the flowing current. Whereas the second largest was presence of cubicle cover the clamp, where the difference of reading hod variation, depend on the size of cubicle. The less of cubicle, the larger of difference of reading While the influences of other external factors were relatively low, belem 10%, with the reference on reading of conventional ammeter |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Jurnal Teknologi Industri |
| Volume / Nomor Edisi | : | XI (No. 4) |
| Nomor Halaman | : | 315-322 |
| Abstraksi Narasi | : | Planning and control raw material in company is purpose to depress the expense, so that in the end will improve the company profitability. PD. TaruMartani is company which is active in production of non migas of cheroot and tobacco shag. Problems faced by PD. TaruMartani how to determine the optimal amount and time of ordering of raw material of tobacco of Kentucky Van Nelle product so that can minimize the raw material inventory expense Way of decision determination to be taken fixed use the company wisdom or by using method which deal with raw material inventory in the plan and operation in company so that planning and control of raw material inventory of tobacco of Kentucky of product of Van Nelle expected can be reached better and efficient Method used in research with the approach model the JIT/EOQ To determine of requirement of the raw material, used forecasting for one year, where the requirement per year 71.414 unit during 12 period (month). Pursuant to research amount of ordering of raw material of tobacco of Kentucky Van Nelle product shall be ax follows to sam up the ordering with the model JIT/EOQ equal to 5512 unit with the total coxt of supply Rp 30 Billion and number delivery 5. But in model JIT/EOQ there are optimal ordering amount that is pursuant to supply capacities 1000 equal to 6038 unit with the total cost supply equal to Rp 28 Billion |
| Nama Pengarang | : | Martunus,Z. Helwati |
| Nama Majalah/Jurnal | : | Jurnal Teknologi Industri |
| Volume / Nomor Edisi | : | XI (No. 4) |
| Nomor Halaman | : | 301-314 |
| Abstraksi Narasi | : | The hold-up of a part of hydrodynamic is of fundamental importance in the design of agitated liquid-liquid extraction column. The design of agitated liquid-liquid extraction columns requires determination of a suitable interfacial area required to achieve a specified degree of mass transfer. The selecting of hold-up correlations with some variables affecting are key component to achieve a specified degree of mass transfer. The correlations of hold-up in RDC are divided into three of equations Le the characteristic velocity, drag relationships and explicit correlations. An explanation for this is presented. |
| Nama Pengarang | : | - |
| Nama Majalah/Jurnal | : | Jurnal Teknologi Industri |
| Volume / Nomor Edisi | : | XI (No. 4) |
| Nomor Halaman | : | 285-300 |
| Abstraksi Narasi | : | A warranty is a contractual agreement between a manufacturer and the consumer, which requires the manufacturer/dealer to rectify all item failures that occur within the warranty period. Warranty can be sold for second hand product with a new contractual agreement. A warranty can be viewed as an alternative of after sales service that plays an important role in product sales. To obtain a second hand product warranty, the consumer must pay an additional cost. This paper studies the warranty policy for a second-hand product sold with two-dimensional warranty. We propose and study a model of second-hand product warranty policies with 3 different alternatives policies based on the coverage region of the warranty. System failure is modeled using the one-dimensional point process formulation where the usage is modeled as a function of time. Parameter estimation for the failure model was done using claim and follow-up data and this results in a more representative reliability model compared. The policy proposed and the corresponding cost models of second-hand product warranty applied for copier. We used claim and follow-up data for copier old in Yogyakarta region from 2005 to 2006 The results of the warranty cost estimation for each alternative are given in this paper |